Quick Answer: How Do You Read A Utility Pole Brand?

What is the diameter of a utility pole?

For example, a class 1 pole has a minimum top circumference of 27 inches.

If it is 25 feet long and cedar (most utility poles are cedar), the circumference measured 6 feet from the bottom must be at least 43.5 inches.

The higher the class number, the skinnier the pole..

How do I find my utility lines?

Typical Utility Line Color CodesWhite: Proposed excavation.Pink: Survey markings.Red: Electric.Yellow: Gas, oil, steam.Orange: Communications, alarms.Blue: Potable water.Purple: Reclaimed water, irrigation.Green: Sewer.

Is it against the law to dig without calling 811?

The law, in all states, generally provides that anyone excavating must call the 811 utility-locate hotline before digging begins to have all utilities located and marked.

How do I find utility lines in my yard?

Anyone who plans to dig should call 811 or go to their state 811 center’s website a few business days before digging to request that the approximate location of buried utilities be marked with paint or flags so that you don’t unintentionally dig into an underground utility line. 811 protects you and your community!

Who owns a utility pole?

A. Beyond the point of supply, the ownership and maintenance of all electrical equipment including power poles, wires and pole-top fittings is the sole responsibility of the property owner.

What does ous mean on a utility pole?

Osmose Utility ServicesBut rather than being graffiti, a gang message or a misspelled reference to The Ohio State University, the marks are actually part of a Penelec maintenance project. And “OUS” is the initials for the Penelec contractor completing the work — Osmose Utility Services.

How much does a utility pole cost?

Cost: From $350 to $1,800. That’s just the pole. Add in labor and equipment costs, and it can cost as much as $3,000 to replace a pole that has been knocked down by, say, a storm or a car.

How deep should a pole be in the ground?

Project Instructions Dig post hole so diameter of the hole is 3 times the width of the post (i.e., the hole for a 4” wood post should be about 12 inches wide). The depth of the hole should be 1/3-1/2 the post height above ground (i.e., a 6-foot tall fence would require a hole depth of at least 2 feet).

How deep are gas and electric lines buried?

Common utility services such as electricity, gas, water and communications cable are usually buried at a depth of 200 – 600mm beneath the surface.

How long does a utility pole last?

25 to 37 yearsA survey of 150 utility companies found the average service life of utility poles to range from 25 to 37 years. The most common reason for replacement being, “strength degradation from ground line decay”.

What are the lines on a power pole?

What Are Each of the Wires on Utility Power Poles?Static Wire. The utmost top line of the utility pole is the static wire. … Transmission Lines. Below the static line are three power lines called transmission lines. … Grounding Conductor. … Primary and Secondary Line. … Neutral Space. … Communications Lines. … Grounding Rod.

What is the distance between two electric pole?

They are typically spaced about 125 ft (38 m) apart in urban areas, or about 300 ft (91 m) in rural areas, but distances vary widely based on terrain. Joint-use poles are usually owned by one utility, which leases space on it for other cables.

How much weight can a utility pole hold?

The horizontal loads that the H-classification poles can hold range from 10,000 lbs. for H5 to 5,400 lbs.

How long does it take to replace a utility pole?

So if there is power and phone on the pole, it might be 120 days before the equipment is moved. Add cable, and it can be 180 days….How much is a meter pole?PriceDescription$60.0025 Foot Pole (No Disconnect or Meter Base)$360.0025 Ft. Pole with Meter Base and 240V/200 Amp Disconnect2 more rows•May 16, 2020

What is the minimum safe distance from power lines?

50 feetMinimum clearance distance (feet) *According to 1926.1409, for power lines over 350 to 1,000 kV, the minimum distance is presumed to be 50 feet. Over 1,000 kV, the utility/owner or a registered engineer must establish it.